 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| CXO3MHG OSCILLATOR 300 kHz to 170 MHz (R) High Shock, Low-Profile Miniature Surface-Mount 3.3 V Crystal Oscillator DESCRIPTION Intended for applications requiring shock survivability to 10,000 g (and higher), Statek's surface-mount CXO3MHG oscillators are high-shock versions of the CXO3M oscillators. These oscillators consist of a Statek miniature quartz crystal and a CMOS/TTL compatible hybrid circuit in a low-profile ceramic package with an extremely small footprint. FEATURES GM M 4.19 actual size side view High shock resistance 3.3 V operation Designed for surface mount applications using infrared, vapor phase, or epoxy mount techniques CMOS and TTL compatible Low power consumption Optional Output Enable/Disable with Tri-State Low EMI emission Full military testing available APPLICATIONS A TOP DIMENSIONS D 2 BOTTOM 3 1 4 D Military & Aerospace Smart munitions Projectile electronics Industrial Engine control Down-hole drilling DIM A B TYPICAL inches 0.256 0.197 mm 6.50 5.00 1.30 1.40 1.40 1.52 MAXIMUM inches 0.263 0.204 0.055 0.063 0.065 0.070 mm 6.68 5.18 1.40 1.60 1.65 1.78 B C E 0.051 C (SM1) C (SM3/SM5) 0.055 SUGGESTED LAND PATTERN 0.067 (1.70) 0.070 (1.78) D E 0.055 0.060 PIN CONNECTIONS 0.065 (1.65) 1. Enable/Disable (E or T) or not connected (N) 2. Ground 0.201 (5.11) 0.136 (3.45) 3. Output 4. VDD 0. 37 (3.48) 1 inches (mm) GRID PLACEMENT COURTYARD S 10172 Rev. A YS TEM CERTIFIC AT N IO STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com IS O 90 01 SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS O Specifications are typical at 25 C unless otherwise noted. Specifications are subject to change without notice. Tighter specifications available. Please contact factory. Supply Voltage1 Calibration Tolerance2 Frequency Stability Over Temperature3 Supply Current (Typical) 3.3 V + _ + _ + _ + _ Supply Voltage VDD -0.5 V to 7.0 V Storage Temperature -55OC to +125OC Maximum Process Temperature 260OC for 20 seconds 10% ENABLE/DISABLE OPTIONS (E/T/N) 100 ppm 50 ppm for Commercial 100 ppm for Industrial + _ 100 ppm for Military 10 MHz 2 mA 24 MHz 4 mA 30 MHz 6 mA 40 MHz 8 mA 50 MHz 10 mA 15 pF 5 ms MAX 6 ns MAX 40% MIN, 60% MAX 10 ppm MAX 10,000 g, 0.3 ms, 1/2 sine 20 g, 10-2,000 Hz swept sine Output Load (CMOS)4 Start-up Time Rise/Fall Time Duty Cycle Aging, first year Shock, survival 5 Statek offers three enable/disable options: E, T, and N. Both the E-version and T-version have Tri-State outputs and differ in whether the oscillator continues to run internally when the output is put into the high Z state: it stops in the E-version and continues to run in the T-version. So, the E-version offers very low current consumption when the oscillator is disabled and the T-version offers very fast output recovery when the oscillator is re-enabled. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table summarizes the three options. COMPARISON OF ENABLE/DISABLE OPTIONS E AND T E When enabled (PIN 1 is high*) Output Oscillator Current consumption When disabled (PIN 1 is low) Output Oscillator Current consumption High Z state Stops Very low Freq. output Oscillates Normal T Vibration, survival6 Operating Temp Ranges -10OC to +70OC (Commercial) -40OC to +85OC (Industrial) -55OC to +125OC (Military) 1. Other voltages available. For 5.0 V, see CXOMHG data sheet. For others, contact factory. 2. Other tolerances available. 3. Does not include calibration tolerance. Other tolerances available. 4. Higher CMOS loads and TTL loads available. Contact factory. 5. Higher shock version available. Contact factory for requirements above 10,000 g. 6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also available. Note: All parameters are measured at ambient temperature with a 10 M, 15 pF load. Freq. output Oscillates Normal High Z state Oscillates Lower than normal When re-enabled (PIN 1 changes from low to high) Output recovery PACKAGING OPTIONS Delayed Immediate CXO3MHG - Tray Pack - 16 mm tape, 7 or 13 reels Per EIA 418 (see Tape and Reel data sheet 10109) * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. HOW TO ORDER CXO3MHG SURFACE MOUNT CRYSTAL OSCILLATORS CXO3MHG S T Enable/Disable Option E, T, or N SM3 Terminations Blank = SM1 = Gold Plated SM3 = Solder Dipped SM5 = Solder Dipped (Lead Free) 32.0M , Frequency K = kHz M = MHz 100 Calibration Tolerance @ 250C (in ppm) / 100 Frequency Stability over Temp.Range (in ppm) / / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified "S" if special or custom design; otherwise blank. OR / / 200 Total Frequency Tolerance (in ppm) / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified S 10172 Rev. A YS TEM CERTIFIC AT N IO STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com IS O 90 01 |
Price & Availability of CXO3MHG
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |